2GIG Go!Control: How to Wire the 2GIG-TAKE Hardwired to Wireless Module

This video show’s end users how they can take their existing hardwired contacts, motion detectors, glass break detectors and use them in conjunction with the 2GIG Go!Control wireless security system.

For the lowest No-Term alarm monitoring rates contact GEOARM Security.

Contact: http://www.geoarm.com/contact.html

Product: http://www.geoarm.com/2gig-take-9-wired-zones-takeover-transmitter-module.html

Alarm Monitoring for new or existing systems : http://www.geoarm.com/alarm-monitoring-services.html

2gig takeover module document

Facebooktwittergoogle_plusredditpinterestlinkedinmail

 Qolsys IQ Panel: DIY How to Install/Program the IQ2 Tablet QW-9100-840-00

DIY How to Install/Program the IQ2 QW-9100-840-00 Tablet into the Qolsys IQ wireless security system.

For the lowest No-Term alarm monitoring rates contact GEOARM Security.
Contact: http://www.geoarm.com/contact.html
Product: http://www.geoarm.com/qolsys-iq-secondary-touchscreen-tablet-qw-9100-840-00.html
Alarm Monitoring for new or existing systems : http://www.geoarm.com/alarm-monitoring-services.html

Facebooktwittergoogle_plusredditpinterestlinkedinmail

 Honeywell’s APL “Advanced Protection Logic”

Hey Everyone Brad Finger here with GEOARM Security. Today we will be talking about Honeywell’s proprietary APL or (Advance Protection Logic.) which is available with LYNX Touch and LYNX Plus L3000 Wireless Security systems.The L3000 must have a revision number of 21.10 or higher to utilize this feature.
Now,In most homes people will set there most frequent points of entry on delay mode. This is where you enter your home and the system gives you around 30 seconds to disarm before it goes into an alarm. Since the brains of the system are all consolidated into the panel there is a risk in placing your panel near one of these delayed zones. If an intruder was to break into your home through one of these delay zones they could run in, grab the system, and either smash it or throw it in a bucket of water rendering the system. Luckily with professional monitoring through GEOARM and the activation of the APL your system will send a ping to our central monitoring station every time one of these delay doors is opened letting us know the system is ok. Once you enter your 4 digit disarm pass code we will receive another signal letting us know you have disarmed your system and it is still in tact. If we don’t receive this final ping we will than treat it as an alarm and reach out to the emergency contact list provided by the client and dispatch if protocol calls for that. In our opinion this feature is a very important feature to activate on your system. If you have any questions please contact us 1-877-443-6276 and be on the look out for many more video blogs to come your way!
Facebooktwittergoogle_plusredditpinterestlinkedinmail

 Honeywell LYNX Touch L5200: How to Wire the Transformer to the Wireless Security System?

Today we will show you how to wire the transformer into the Honeywell LYNX Touch L5200 wireless security system. You will need the L5200 transformer, the alarm panel itself, a 22 gauge by 2 wire, and lastly a flat head screw driver. Depress the two tabs on the top of the system, be very careful laying the system down because you do not want to damage the 4.7 inch touch screen display. You will see both ends of the wire will be prepared differently. The end that is meant to get wired into the transformer will have less conduit exposed and more of the actual copper exposed. With the extra copper exposed you will see that you than want to take the ends and make two hooks with the ends, this will help you when you wrap them around the screws on the transformer. The other end of the wire will be going through the back mounting plate. On this side of the wire you will see their is more of the conduit exposed and less copper, this is so when you place the wire ends into the terminals there is less of a chance to have any copper exposed which could short your panel out. After you have place the red wire around the positive terminal on the transformer go ahead and do the same for the black wire to the negative terminal on the transformer You can go ahead and place the transformer down for the time being. Now go ahead and run the wire through the area as shown on the video and wire the red wire into the 9vdc this is where your red wire will go and GND is where your black wire will go. Now close your system up make sure the two depressions snap together and your all ready to give your wireless security system power!

For all of the how to videos we have on this panel visit our YouTube Channel

For alarm monitoring on this panel vistit our webpage

Facebooktwittergoogle_plusredditpinterestlinkedinmail

 How to Wire the Transformer to a Honeywell L3000 Wireless Security System?

To start you want to depress the two tabs at the top of the system. Gently place the system down so that you don’t crack the screen. You will need a 22 gauge by 2 wire cut to the length from the panel to the outlet itself. You will notice each side of the wire will be prepared in different manners. The side that is going to the transformer will have less of the conduit cut off but more of the actual red and black wire will be cut to expose more copper. Once you have the copper exposed you than want to hook both the red wire and the black wire to loop around the two screws located on the back of the transformer. For the other end of the conduit which will be wired behind the mounting plate, you want to expose more of the conduit and less of the copper so no copper is exposed. Once the transformer has been wired go ahead and run the other end of the wire through the back of the mounting plate tie a knot so the wire does not try to pull itself out of the terminals. A fun fact about this Honeywell LYNX Plus panel is that it uses AC current not DC current so there is not polarity. When screwing the wires into the terminal be cautious not to screw in too hard because you are screwing a metal screw into a plastic terminal. Your Honeywell LYNX Plus L3000 wireless security system is now wired you are ready to sign up for professional monitoring!

Follow our GEOARM YouTube page for all of the updated how to videos.

Facebooktwittergoogle_plusredditpinterestlinkedinmail