How to Wire the IGSMV4G to the Honeywell Vista 21IP Hardwired Security System

Before attempting to install the Honeywell IGSMV4G Dual path communicator into your Vista 21IP hardwired system please make sure to power down the system including your backup battery and your transformer. Once this has been completed make sure that you have watched our previous video which will show you how to move the jumper on your 21IP system to the proper position in order to allow for external communicators. The first thing your going to want to do is run the 22 gauge by 4 wire through the back of the panel and begin wiring up the panel first. Take the black wire which will be the ground wire and make sure that goes into terminal 4. The second wire will be the power wire which of course is red place this in terminal 5. The yellow wire will go to terminal 7 and green will go to terminal 6 these two are your data in and data out terminals. Now that these are in place lets take the opposite side of the 22 gauge by 4 wire and begin to wire up the IGSMV4G dual path communicator.

Continuing on lets start by wiring in the ground or the black wire which will go into terminal 4. Next will be the red wire or “power” which will go into terminal 3. Terminal 5 you will want to wire in the yellow wire and lastly 6 will be your green wire again both of these are data in and data out. With this being wired up now you are ready to plug in your K14138LF wire which is what connects the communicator to the backup battery. Just a fun fact terminal one and two are for you ac transformer if you decide to wire in that way. Also, keep in mind you should always follow along with your instructions while working with your alarm panel.

For the lowest No-Term alarm monitoring rates contact GEOARM Security.
Contact: http://www.geoarm.com/contact.html
Product: http://www.geoarm.com/vista-21ip-honeywell-dual-path-security-system.html
Alarm Monitoring for new or existing systems : http://www.geoarm.com/alarm-monitoring-services.html

 

Facebooktwittergoogle_plusredditpinterestlinkedinmail

 GE Simon XT V2: How to Change the Time on your Wireless Security System

 

In this video you will be getting a walk through on how to change the time on your GE Simon XT V2 wireless security system. To change the time on the Simon XT, you will have to hit the down arrow button to navigate through your panel until you see “Set Clock”, then press the OK button. Enter your  default installer code 4321 than hit OK. After you enter your code it will ask you too “Set Clock”, So with the same arrow navigation buttons you can manipulate the time. Now it will first ask you to change the hour once you selected the correct hour option select OK, next it will prompt you to enter in the current minute, after you have entered in the correct minutes select OK and lastly select whether it is currently am or pm. After your time looks accurate go ahead and select the ok button one last time and hit the status button to exit out of this field.

How to change the time on your GE simon xt v2 wireless security system.

For the lowest No-Term alarm monitoring rates contact GEOARM Security.
Contact: http://www.geoarm.com/contact.html
Product: http://www.geoarm.com/ge-simon-xt-wireless-security-systems.html
Alarm Monitoring for new or existing systems : http://www.geoarm.com/alarm-monitoring-services.html

 

Facebooktwittergoogle_plusredditpinterestlinkedinmail

 DSC Touch Wireless Security System Overview by GEOARM Security


This is a brand new  video that we are releasing in honor of the Tyco/DSC Touch wireless security system to show the end user all of the new cool features and benefits of this wireless security system.

 

For the lowest No-Term alarm monitoring rates contact GEOARM Security.

Contact: http://www.geoarm.com/contact.html

Product: http://www.geoarm.com/alarm-com-basic-interactive-cellular-gsm-alarm-monitoring.html

Alarm Monitoring for new or existing systems : http://www.geoarm.com/alarm-monitoring-services.html

Facebooktwittergoogle_plusredditpinterestlinkedinmail

 How to Install the Qolsys IQ Wireless Siren?

Today we will show you how to install the Qolsys IQ Siren (QS-QZ2300-840). The IQ Siren has a 105DB output which is extremely loud and it has a rechargeable back up battery to give you extended life even if the power goes out.The QS-QZ2300-840 Siren plugs into any standard wall outlet making a DIY install fast and easy. Not only is it loud but, it also has three strobe lights that flash when the alarm goes off which gives you double the protection!

How to Install the QS-QZ2300-840 Siren in conjunction with your Qolsys IQ wireless security system.

For the lowest No-Term alarm monitoring rates contact GEOARM Security.
Contact: http://www.geoarm.com/contact.html
Product: http://www.geoarm.com/qolsys-iq-wireless-alarm-siren-qs-qz2300-840.html
Alarm Monitoring for new or existing systems : http://www.geoarm.com/alarm-monitoring-services.html

Facebooktwittergoogle_plusredditpinterestlinkedinmail

 Qolsys IQ Panel: How to Program the QS-1112-P01 Wireless Mini-Door/Window Contact

To pair your QS-1112-P01 to your Qolsys IQ Wireless panel put your IQ panel in auto learn mode. Make sure you have the QS-1112-P01 Mini contact already installed before you try to do the auto learn process. To get to the auto learn mode go to settings, it will ask you to enter in the default installer code, once completed go to installation, security sensors, than auto learn sensor.

When you have entered auto learn mode on your Qolsys Iq wireless panel open ,the door/window to start the auto learning process. You should hear a chime upon opening the zone, next a prompt will come up select OK to add the sensor. Once you add the sensor it will display what type of sensor it is. You can change the name of the sensor to any pre-filled name or customize your own  zone description name. The system allows you to select a custom chime for every door/window in the home or you can make your own chime for each sensor “we recommend using one of the pre-exiting chimes”. When you choose a sensor group, the sensor group will tell your sensors how to behave. So for example if you want to use any door to enter or exit, set it as the “Entry/Exit normal delay”. If you didn’t want to have any delay on that specific zone you would want to select instant/perimeter.

For the lowest No-Term alarm monitoring rates contact GEOARM Security.

Contact: http://www.geoarm.com/contact.html

Product: http://www.geoarm.com/qolsys-iq-wireless-mini-door-window-alarm-contact-qs-1112-p01.html

Alarm Monitoring for new or existing systems : http://www.geoarm.com/qolsys-interactive-alarm-com-monitoring-services.html

Facebooktwittergoogle_plusredditpinterestlinkedinmail