Archive for the 'Wireless Products' Category

 AlarmClub Announces the Release of the Honeywell SiXSMOKE

Honeywell Lyric SiXSMOKE Wireless Smoke Detector

Honeywell Lyric SiXSMOKE Wireless Smoke Detector

The Honeywell Lyric SiXSMOKE has finally been released and is available for shipping within the USA and Canada. The SiXSMOKE was announced at the same time as all of the other SiX Series sensors and where available for ordering but, these sensors were delayed for a few months. The Lyric smoke detector is compatible with the Honeywell Lyric Controller and other systems that can utilize SiX sensor. Once the SiXSMOKE is enrolled into the panel, it cannot be used with another control panel until it has been deleted first because of the Lyric Lock feature. Each Lyric smoke detector has a unique MAC number located on the sticker on the unit.

The wireless SiXSMOKE has a maximum coverage area of 50′ X 50′ and detects smoke/heat in two ways Fixed =135° F Heat Sensing and Rate-of-Rise Sensing of =15° F within 1 minute. One of the coolest features of the Lyric SiXSMOKE, when paired with a Lyric Controller is the fact that if you have more than one detector you can set up the One Go All Go feature which will activate all SiXSMOKE’s if one is triggered. You can place the Lyric SiXSMOKE within 300 feet of the alarm control panel which allows you to install in those back areas. The SiXSMOKE works on a a Direct Sequence, Spread Spectrum (DSSS), two-way radio utilizing the 2.4GHz RF band. In the 2.4GHz band, there are 16 channels available for SiX™. When the device registers with the control panel, it will automatically determine which frequency channel the panel is operating on.

When the SiXSMOKE photoelectric beam detects the presence of smoke, it will go into alarm and send the alarm signal to the Lyric Controller. The Lyric SiXSMOKE works best when you have professional alarm monitoring for your Lyric Security System. Once our central alarm monitoring station receives these signals we can dispatch the exact fire department for your area. During an alarm condition, pressing the detectors test switch will silence the piezoelectric horn for 5 minutes. When programmed in one-go-all-go mode, the detector can only be silenced from the controller. When the battery of the Lyric SiXSMOKE is no longer working you will need to replace it with One 3V lithium battery. Duracell DL123 and DL123A, Panasonic CR123A, Honeywell 466. Remove batteries for at least 10 seconds, before installing new ones.

Note: Do not mix old and new batteries, battery types or manufacturers. 

Honeywell SiXSMOKE Frequently Asked Questions

Honeywell SiXSMOKE Product Manuals

Facebooktwittergoogle_plusredditpinterestlinkedinmail

 How to Replace the Battery in the Honeywell 5853 Wireless Glass Break Sensor?

Today we are going to show you how to replace the battery in the Honeywell 5853 wireless glass break detector. This Honeywell 5853 wireless glass break detector uses a CR123A 3V battery.  Now go ahead and open the sensor by prying the top open allowing for the front plate to fall down. Go ahead and pull the old battery out, grab your new matching battery and slide the new battery into place. Look for the two lights on the bottom to flash and than seal the front plate back in place and you are all set you can expect another 3-5 years of service from this battery depending on how often it is in use.

For the lowest No-Term alarm monitoring rates contact GEOARM Security.
Contact: http://www.geoarm.com/contact.html
Product: http://www.geoarm.com/honeywell-wireless-glassbreak-detector-5853.html
Battery: http://www.geoarm.com/123-lithium-battery-cr123-dl123a-el123ap-el123apbp.html
Alarm Monitoring for new or existing systems : http://www.geoarm.com/alarm-monitoring-services.html

Facebooktwittergoogle_plusredditpinterestlinkedinmail

 GE Simon XT V2: How to Set the Date on your Wireless Security System

 

In this video we will be showing you how to set the date on the Simon XT V2. First you will scroll down by using the down arrow button until you get to “Set Date”, press the OK button. Enter your default installer code to access the programming to change the date. Then you will press OK to start changing the year by pressing the up or down arrow. Once you have the year entered correctly select OK to switch to the month. Once you have chosen the appropriate month continue by pressing the OK button. Now you will be prompted to change the actual day, once this has been completed make sure you press OK. Once you are finished programming the new date press the status button to exit you out of programming.

For the lowest No-Term alarm monitoring rates contact GEOARM Security.

Contact: http://www.geoarm.com/contact.html
Product: http://www.geoarm.com/ge-simon-xt-wireless-security-systems.html
Alarm Monitoring for new or existing systems : http://www.geoarm.com/alarm-monitoring-services.html

 

Facebooktwittergoogle_plusredditpinterestlinkedinmail

 GE Simon XT V2: How to Change the Time on your Wireless Security System

 

In this video you will be getting a walk through on how to change the time on your GE Simon XT V2 wireless security system. To change the time on the Simon XT, you will have to hit the down arrow button to navigate through your panel until you see “Set Clock”, then press the OK button. Enter your  default installer code 4321 than hit OK. After you enter your code it will ask you too “Set Clock”, So with the same arrow navigation buttons you can manipulate the time. Now it will first ask you to change the hour once you selected the correct hour option select OK, next it will prompt you to enter in the current minute, after you have entered in the correct minutes select OK and lastly select whether it is currently am or pm. After your time looks accurate go ahead and select the ok button one last time and hit the status button to exit out of this field.

How to change the time on your GE simon xt v2 wireless security system.

For the lowest No-Term alarm monitoring rates contact GEOARM Security.
Contact: http://www.geoarm.com/contact.html
Product: http://www.geoarm.com/ge-simon-xt-wireless-security-systems.html
Alarm Monitoring for new or existing systems : http://www.geoarm.com/alarm-monitoring-services.html

 

Facebooktwittergoogle_plusredditpinterestlinkedinmail

 How to Install the Qolsys IQ Wireless Siren?

Today we will show you how to install the Qolsys IQ Siren (QS-QZ2300-840). The IQ Siren has a 105DB output which is extremely loud and it has a rechargeable back up battery to give you extended life even if the power goes out.The QS-QZ2300-840 Siren plugs into any standard wall outlet making a DIY install fast and easy. Not only is it loud but, it also has three strobe lights that flash when the alarm goes off which gives you double the protection!

How to Install the QS-QZ2300-840 Siren in conjunction with your Qolsys IQ wireless security system.

For the lowest No-Term alarm monitoring rates contact GEOARM Security.
Contact: http://www.geoarm.com/contact.html
Product: http://www.geoarm.com/qolsys-iq-wireless-alarm-siren-qs-qz2300-840.html
Alarm Monitoring for new or existing systems : http://www.geoarm.com/alarm-monitoring-services.html

Facebooktwittergoogle_plusredditpinterestlinkedinmail