Archive for the 'Alarm Communicators' Category

 How to Install the 600-1053-3-ZWAVE-AT Cellular Radio into the GE Concord 4 Hybrid Alarm System?

Today we are going to show you how to install the 600-1053-3-ZWAVE-AT into the ge concord 4 hybrid alarm system. Make sure you you power down the system and unplug the backup battery before attempting this. Now, the first thing you will want to do is do open the box the communicator comes in and empty all of the contents. Enclosed you should find the cellular communicator, a package with the red power cable to link the cellular communicator to the alarm panel, and the instruction manual. Make sure to keep the packaging in resell able condition in case for whatever reason you need to make a return to Geoarm. Locate the 600-1053-3-ZWAVE-AT , the clear package with the red power cable, and the 22 gauge by 4 wire. Once this is all arranged open the cell module by depressing the button at the top of the communicator. After you have exposed the insides of the 600-1053-3-ZWAVE-AT take the antenna which is run through the bottom and you are going to run the wires as shown on figure 2. Now that you have the antenna run, we are going to focus on wiring the actual cellular module. Take the red wire with the fuse and follow along with figure 3. As shown you will run the red wire through the back and wire it into the terminal labeled 12v the opposite end of this wire wiill eventually get wired to the positive terminal in the alarm systems backup battery. Next, take the 22 gauge by 4 wire run that through the back of the cellular module as well. The first wire that will be wired will be the green wire and you will screw that into the terminal labeled A. Moving on to the next color wire you will want to gather the white wire and screw that into the terminal labeled B. The last wire you are going to work with is the ground wire which is black in color wire that into the terminal labeled GND. Now that your cell module has been wired up its time to wire the opposite ends into the panel itself. Now that you can see the cellular module all wired up bring this device near the GE Concord 4 Hybrid alarm system. Notice that there are several knockouts on the can itself. Select the knockout either under the board run the wires through that knockout and now we will begin wiring to the panel. So as you can see the black wire or ground wire will go into terminal 3 which will also be labeled GND. The green cable is going to get wired into terminal 5 which is also labeled terminal A, and lastly the white wire will get placed into terminal 6 which is labeled terminal B.

For the lowest No-Term alarm monitoring rates contact GEOARM Security.

Contact: http://www.geoarm.com/contact.html

Product: http://www.geoarm.com/600-1053-3-zwave-at-ge-alarm-com-concord-wireless-3g-cellular-alarm-communicator-for-att.html

Alarm Monitoring for new or existing systems : http://www.geoarm.com/alarm-monitoring-services.html

Facebooktwittergoogle_plusredditpinterestlinkedinmail

 How to Wire the IGSMV4G to the Honeywell Vista 21IP Hardwired Security System

Before attempting to install the Honeywell IGSMV4G Dual path communicator into your Vista 21IP hardwired system please make sure to power down the system including your backup battery and your transformer. Once this has been completed make sure that you have watched our previous video which will show you how to move the jumper on your 21IP system to the proper position in order to allow for external communicators. The first thing your going to want to do is run the 22 gauge by 4 wire through the back of the panel and begin wiring up the panel first. Take the black wire which will be the ground wire and make sure that goes into terminal 4. The second wire will be the power wire which of course is red place this in terminal 5. The yellow wire will go to terminal 7 and green will go to terminal 6 these two are your data in and data out terminals. Now that these are in place lets take the opposite side of the 22 gauge by 4 wire and begin to wire up the IGSMV4G dual path communicator.

Continuing on lets start by wiring in the ground or the black wire which will go into terminal 4. Next will be the red wire or “power” which will go into terminal 3. Terminal 5 you will want to wire in the yellow wire and lastly 6 will be your green wire again both of these are data in and data out. With this being wired up now you are ready to plug in your K14138LF wire which is what connects the communicator to the backup battery. Just a fun fact terminal one and two are for you ac transformer if you decide to wire in that way. Also, keep in mind you should always follow along with your instructions while working with your alarm panel.

For the lowest No-Term alarm monitoring rates contact GEOARM Security.
Contact: http://www.geoarm.com/contact.html
Product: http://www.geoarm.com/vista-21ip-honeywell-dual-path-security-system.html
Alarm Monitoring for new or existing systems : http://www.geoarm.com/alarm-monitoring-services.html

 

Facebooktwittergoogle_plusredditpinterestlinkedinmail

 Qolsys IQ Panel: Connecting the System to Wi-Fi

Connecting the system to Wi-Fi with your Qolsys IQ Wireless security panel.

For the lowest No-Term alarm monitoring rates contact GEOARM Security.
Contact: http://www.geoarm.com/contact.html
Product: http://www.geoarm.com/qolsys-iq-wireless-security-system.html
Alarm Monitoring for new or existing systems : http://www.geoarm.com/alarm-monitoring-services.html

Facebooktwittergoogle_plusredditpinterestlinkedinmail

 Ge Simon XT V2: DIY How to Install the 600-1048-XT-ZX-VZ Cellular Communicator

 

DIY How to Install the 600-1048-XT-ZX-VZ Cellular Communicator into the GE Simon XT V2 wireless security system. By following this video working with this GE Simon XT wireless security system has never been so easy!

For the lowest No-Term alarm monitoring rates contact GEOARM Security.
Contact: http://www.geoarm.com/contact.html
Product: http://www.geoarm.com/600-1048-xt-zx-vz-ge-alarm-com-simon-xt-wireless-cdma-cellular-alarm-communicator-for-verizon.html
Alarm Monitoring for new or existing systems : http://www.geoarm.com/alarm-monitoring-services.html

Facebooktwittergoogle_plusredditpinterestlinkedinmail

 Honeywell LYNX Touch L5200: DIY How to Install the 3GL Cellular Communicator?

 

Today i am going to show you how to install the 3GL cellular communicator into the LYNX Touch L5200 wireless security system. Note: Before working with your Honeywell LYNX touch l5200 unplug the backup battery and make sure the l7000 transformer is detached from any power outlet. Organize all of the contents of the wireless security system and the cellular communicator. You will be working with three screws, the 3gl module, and the cellular card. When opening all of these boxes make sure to keep packaging in re sell-able condition in case you need to return the items for any reason.

Depress the two tabs located on the top of the Honeywell L5200 wireless security system. I like to you use a small flat head screw to open the panel. Take the GSM chip that comes with the 3gl cellular communicator. Locate the side on the chip that says gsm. That part will slide into the female slot on the 3gl cellular communicator. Once that has been completed locate the 3 screw terminals in the bottom left of the system and as shown on our video. Align the screws and communicator in their designated slots. Once all three screws have been inserted your communicator is now in place. Locate the Mac and Mac Crc numbers off of the communicator and make note of that as you will need this to activate cellular monitoring with GEOARM. Plug in your backup battery make sure your transformer is wired correctly, seal the panel up and plug in your transformer and Call us so we can schedule your tech appointment to go online with our remote tech support!

Facebooktwittergoogle_plusredditpinterestlinkedinmail