The DIY Security Blog

April 26, 2017

How to Install the Qolsys IQ Panel 2 Security System

Qolsys IQ Panel 2 How-to-Video Playlist


Here you will learn how to install the Qolsys IQ Panel 2 wireless security system. The first step to installing the IQ Panel 2 is to open the box and remove the contents such as the installation manual, IQ Panel 2, S-Line Motion sensor, power supply, table stand and 3 S-Line mini door/window sensors. Now that you have removed all of the products out of the manufactures box you want to make sure that you organize all of your parts together so you don’t misplace any of them.

The second part of the IQ Panel 2 installation is to locate the touchscreen and remove the back plate where you will now see the insides of the panel. Inside the panel, you will want to locate the female end where the power supply cable will plug right in. After you have completed plugging in the power transformer you can replace the back panel plate and install the Qolsys IQ panel 2 table stand which simply slides into place. Now that you have completed all of the above steps its time to plug in the power transformer so the IQ panel to can power up. The thirds step after powering up the Qolsys IQ panel 2 is to run a cellular test.

The thirds step after powering up the Qolsys IQ panel 2 is to run a cellular test. To run a cellular test on the IQ panel 2 simply slide your finger down hit settings > Advanced Settings > enter default Qolsys installer codes “1111” > system tests > Cellular tests > Start. The cellular test is one of the most important aspects of your IQ panel 2 installations because without good cellular signal strength you run the risk of your system giving you communication failures. During the cellular signal strength test, your technician will work with you remotely to make sure that you install the IQ panel 2 in a location that will allow for good communications. After you have found a good location for either table or wall mounting its time to move onto the next step of installation.

The fourth step in the Qolsys IQ Panel 2 installation process is to connect your panel to Wi-Fi network. To connect the panel to the Wi-Fi network from the IQ panel 2 touchscreen scroll down > select settings > Advanced Settings > enter you installer code “1111” > Wi-Fi > check the box in the top right of screen > Select your Wi-Fi network. Connecting to Wi-Fi is not always necessary because the Qolsys IQ panel 2 can function on cellular only but, it does offer some key advantages such as, dual-path communications which gives end users a much more reliable means to communicate alarm signals to the central station. In addition, Wi-Fi offers end-users a much easier means of connecting the secondary keypad called the IQ remote because the remote is connected primarily via Wi-Fi network. When using Wi-Fi a wifi connection end users will use less data whenever they remotely arm/disarm with application and or attempt to update the IQ panel to firmware updates. Even if you don’t have a Wi-Fi connection you can still connect the IQ remote to the IQ panel 2 unlike the IQ Panel ( 1st generation) because the IQ panel 2 has a built-in router. If you have both Wi-FI and cellular connection activated the system by default will use Wi-Fi as the primary mode of communication and the cellular as the backup to conserve data. In the past Wi-Fi connections have been a bit quicker but now with the IQ panel 2 adding 4G LTE communications that is not so much the case anymore.

The fifth step in the installation process will be to check for remote firmware updates to make sure your panel is running on the latest firmware. To check for firmware updates from the home screen slide down > Select Settings > Advanced Settings > enter installer code “1111” > upgrade software > upgrade using network. Just like any kind of technology making sure your IQ panel has the latest firmware update is a necessity and with the snapdragon Android 5+ platform, it has never been easier.

The sixth step in the IQ Panel 2 installation process is to install you encrypted security sensors and z-wave home automation devices. Qolsys has made the programming of these sensors easier than ever and has a very detailed diagram that will be included in this document. In the future, we will be creating how-to videos to show you exactly how this process is done. The IQ panel 2 allows for up to 128 S-Line encrypted sensors and or older non-encrypted sensors which are perfect for upgrades. The same goes for Z-wave home automation devices the IQ Panel 2 can handle up to 128 z-wave plus devices & sensors.

In conclusion, the Qolsys IQ Panel 2 is an extremely innovative wireless security system that has opened the door for easy DIY installation applications. This can be seen with their true all-in-one design. All of the necessary communicators and modules have been built into the panel so in reality, the only thing that a DIYer needs to do is plug in the DC Power supply giving power to the main IQ Panel 2. After the end-user supplies power to the panel, everything else can be supported remotely with instructions from an offsite technician. Since Qolsys teamed up with interactive monitoring services this opens up a huge advantage to the DIY market. Once the panel has power technicians can remotely access the IQ Panel 2 programming menu to assist in programming security sensors and changing the way the end user wants them to react in the event of a triggered alarm, assist in changing user codes, resetting the panel and much more.

Qolsys IQ Panel 2 Installation

Qolsys IQ Panel 2 Installation

Qolsys IQ Panel 2 How to Videos

Qolsys IQ Panel 2 Product Manuals

Qolsys IQ Panel 2 Frequently Asked Questions




March 16, 2017

ADC-SEM-100-CDMA / ADC-SEM-100-LTE: Installation to Honeywell Vista Systems

Here you will learn how to install the ADC-SEM-100-CDMA / ADC-SEM-100-LTE cellular communicator into Honeywell Vista security systems. Compatible Vista panels are as follows Vista 10p/10psia, 15p/15psia, 20p/20psia and 21ip wired systems. In the past typically Honeywell Vista panels would achieve interactive alarm monitoring services by using their own Total Connect application. Now, customers have another option to add to the list.

The ADC-SEM-100-CDMA / ADC-SEM-100-LTE uses for reporting of alarms and other system events using the CDMA/LTE networks. The SEM is meant to be used as the primary communication path for all alarm signals to our central monitoring station. Once installed and activated the SEM module allows for remote operation by the customer from their smart devices. They will have the ability to access the system at any time from any location. Additional features include viewing system and sensor status/ history, remote arming/disarming, setting up and managing user codes, creating customized email and text notifications for any type of alarm or none- alarm activity at their property. The SEM cellular communicator also supports home automation services due to its built in z-wave receiver.

Tools and Supplies needed to complete the SEM installation

• Wire and fuse – Included

• 3 screws for mounting – Included

• Wall Anchors for mounting – Included

• Small flathead and Phillips screwdriver

• Drill and bits – optional

• Four-conductor 22-guage or larger stranded wire

Honeywell Alpha programming keypad  – Recommended for installation SEM (System Enhancement Module) Monitoring services SEM Cellular CDMA Communicator for Vista Panels SEM Cellular CDMA Communicator


November 11, 2016

AlarmClub Announces the Release of the Honeywell SiXSMOKE

Honeywell Lyric SiXSMOKE Wireless Smoke Detector

Honeywell Lyric SiXSMOKE Wireless Smoke Detector

The Honeywell Lyric SiXSMOKE has finally been released and is available for shipping within the USA and Canada. The SiXSMOKE was announced at the same time as all of the other SiX Series sensors and where available for ordering but, these sensors were delayed for a few months. The Lyric smoke detector is compatible with the Honeywell Lyric Controller and other systems that can utilize SiX sensor. Once the SiXSMOKE is enrolled into the panel, it cannot be used with another control panel until it has been deleted first because of the Lyric Lock feature. Each Lyric smoke detector has a unique MAC number located on the sticker on the unit.

The wireless SiXSMOKE has a maximum coverage area of 50′ X 50′ and detects smoke/heat in two ways Fixed =135° F Heat Sensing and Rate-of-Rise Sensing of =15° F within 1 minute. One of the coolest features of the Lyric SiXSMOKE, when paired with a Lyric Controller is the fact that if you have more than one detector you can set up the One Go All Go feature which will activate all SiXSMOKE’s if one is triggered. You can place the Lyric SiXSMOKE within 300 feet of the alarm control panel which allows you to install in those back areas. The SiXSMOKE works on a a Direct Sequence, Spread Spectrum (DSSS), two-way radio utilizing the 2.4GHz RF band. In the 2.4GHz band, there are 16 channels available for SiX™. When the device registers with the control panel, it will automatically determine which frequency channel the panel is operating on.

When the SiXSMOKE photoelectric beam detects the presence of smoke, it will go into alarm and send the alarm signal to the Lyric Controller. The Lyric SiXSMOKE works best when you have professional alarm monitoring for your Lyric Security System. Once our central alarm monitoring station receives these signals we can dispatch the exact fire department for your area. During an alarm condition, pressing the detectors test switch will silence the piezoelectric horn for 5 minutes. When programmed in one-go-all-go mode, the detector can only be silenced from the controller. When the battery of the Lyric SiXSMOKE is no longer working you will need to replace it with One 3V lithium battery. Duracell DL123 and DL123A, Panasonic CR123A, Honeywell 466. Remove batteries for at least 10 seconds, before installing new ones.

Note: Do not mix old and new batteries, battery types or manufacturers. 

Honeywell SiXSMOKE Frequently Asked Questions

Honeywell SiXSMOKE Product Manuals


November 1, 2016

Review of the Honeywell Lyric Secondary Keypad (LKP500-EN)

Filed under: FAQ's,Honeywell Lyric,Honeywell SiX — Brad @ 12:24 pm

Honeywell LKP500-EN secondary Lyric Keypad

Honeywell LKP500-EN secondary Lyric Keypad

The Honeywell Lyric Secondary keypad (LKP500-EN) is small in size, which makes it perfect for mounting in those hard-to-fit places. The sleek and stylish product design, allows the keypad to blend into any decor. The installation of the keypad is easy with choices of either wall-mounting or optionally using a Lyric Desk stand kit (LKP500-DK) which is great if you are planning on DIY installing on tabletops, nightstands or kitchen counter. A big benefit of the Lyric Secondary Keypad is its range. Previous 5828/5828v keypads could not be placed further than 50 feet while LKP500-EN has a listed wireless range of 300ft!

The LKP500-EN is the Honeywell wireless secondary keypad that works with systems that work with SiX Series encrypted technology such as the Honeywell Lyric Controller. The Lyric Keypad takes advantage of the 2.4ghz channel which offers full 128-bit encryption to prevent intruders from jamming the RF signals. With the LKP500-EN you also get a keypad that is fully supervised. This means that the Lyric Keypad sends signals back to the alarm control panel every 60 seconds making sure it is still within range. If the Lyric Controller does not receive this signal a supervision loss signal will be sent to our professional alarm monitoring station and if you have Total Connect Services activated with AlarmClub you will receive text and email notifications to your smartphone.

The Lyric Keypad allows you quickly arm/disarm the Honeywell Lyric Security System as well as listen to system status updates with its built-in speaker. One of the greatest benefits of the Lyric LKP500-EN keypad is its panic button features for police, fire, and medical purposes. The Lyric Controller will allow up to 8 LKP500-EN to be programmed at any given time. We recommend adding multiple LKP500-EN wireless Lyric Keypads spread out by the most frequently entered and exited locations such as front doors, garage doors, and master bedrooms.

With the Honeywell LKP500-EN you will have access to its own settings menu where you can adjust features such as turn chime on and off, toggle exit tone/entry tone, voice volume, key level, display brightness, and backlight brightness. To access this area of Lyric Keypad settings simply press and hold select key until menu begins, use the scroll key to the settings, use the select key to choose from desired menu item, use the scroll key to toggle menu options, press select key to save your settings and press cancel at any time to exit Lyric Keypad settings menu. When firmware updates are available for this product you can upgrade the software by manually or remotely by AlarmClub. To upgrade the Lyric LKP500-EN software locally go to the Lyric Controller programming menu select security, tools, enter the master code by default which is 1234, advanced, upgrade sensor firmware. After performing the upgrade command, the keypad displays the upgrade status then, when done, automatically resets twice. Once the Lyric Keypad completes the reset, it will return to normal operation.

Honeywell SiX Series encrypted security sensors.

Honeywell SiX Series encrypted security sensors.

Programming the Honeywell LKP500-EN secondary keypad is accomplished through the Lyric Controller installer programming menu. To access this area of programming on the controller you must have your installer code. The Lyric Controller Installer code is 4112. Once you access the installer menu select Program. This area of the Lyric control panel programming is the same area that you would program a Honeywell SiXCT door/window contact, Honeywell SiXPIR motion sensor, Honeywell SiXGB, or a Honeywell SiXSIREN although the programming tactics would vary from device to device.

The Honeywell LKP500-EN product includes:

• Battery pack (7.2VDC) provides 24-hour backup battery power (Included)

• An external 110VAC input/9VDC output power pack and cable (Included)


Honeywell LKP500-EN FAQ’s

Honeywell LKP500-EN Product Manuals


March 18, 2016

How to Add User Codes into the 2GIG GC3 Wireless Security?

Knowing the basic functions and features of your 2GIG GC3 wireless security system is very convenient. So today we want to show you how you and or your family members can add user codes into the 2GIG GC3 wireless security and home automation system. To do this Select system settings, enter your default installer code “1561”, users, select the plus sign in the top right of the screen, enter the desired name, next, assign a security code, confirm the code by entering a second time, next, verify your information, select back button to exit programming.
Having individual codes for each user is a very important feature because every time that code is used whether its arming, disarming, programming or making any kind of changes to the system you can always view this information in the system event history log and or setup notifications through interactive alarm monitoring services with GEOARM.

For the lowest No-Term alarm monitoring rates contact GEOARM Security 1-877-443-6276. Make sure to subscribe to our YouTube page so you can keep track of all of the new how-to/product videos from all of the top security system manufactures such as, Honeywell, DSC, Qolsys, GE, 2GIG, Napco, Telular etc…






Alarm Monitoring:



Older Posts »

Powered by GEOARM®