Archive for the 'Installation & Setup' Category

 How to Replace the Battery in the Honeywell 5853 Wireless Glass Break Sensor?

Today we are going to show you how to replace the battery in the Honeywell 5853 wireless glass break detector. This Honeywell 5853 wireless glass break detector uses a CR123A 3V battery.  Now go ahead and open the sensor by prying the top open allowing for the front plate to fall down. Go ahead and pull the old battery out, grab your new matching battery and slide the new battery into place. Look for the two lights on the bottom to flash and than seal the front plate back in place and you are all set you can expect another 3-5 years of service from this battery depending on how often it is in use.

For the lowest No-Term alarm monitoring rates contact GEOARM Security.
Contact: http://www.geoarm.com/contact.html
Product: http://www.geoarm.com/honeywell-wireless-glassbreak-detector-5853.html
Battery: http://www.geoarm.com/123-lithium-battery-cr123-dl123a-el123ap-el123apbp.html
Alarm Monitoring for new or existing systems : http://www.geoarm.com/alarm-monitoring-services.html

Facebooktwittergoogle_plusredditpinterestlinkedinmail

 How to Wire the IGSMV4G to the Honeywell Vista 21IP Hardwired Security System

Before attempting to install the Honeywell IGSMV4G Dual path communicator into your Vista 21IP hardwired system please make sure to power down the system including your backup battery and your transformer. Once this has been completed make sure that you have watched our previous video which will show you how to move the jumper on your 21IP system to the proper position in order to allow for external communicators. The first thing your going to want to do is run the 22 gauge by 4 wire through the back of the panel and begin wiring up the panel first. Take the black wire which will be the ground wire and make sure that goes into terminal 4. The second wire will be the power wire which of course is red place this in terminal 5. The yellow wire will go to terminal 7 and green will go to terminal 6 these two are your data in and data out terminals. Now that these are in place lets take the opposite side of the 22 gauge by 4 wire and begin to wire up the IGSMV4G dual path communicator.

Continuing on lets start by wiring in the ground or the black wire which will go into terminal 4. Next will be the red wire or “power” which will go into terminal 3. Terminal 5 you will want to wire in the yellow wire and lastly 6 will be your green wire again both of these are data in and data out. With this being wired up now you are ready to plug in your K14138LF wire which is what connects the communicator to the backup battery. Just a fun fact terminal one and two are for you ac transformer if you decide to wire in that way. Also, keep in mind you should always follow along with your instructions while working with your alarm panel.

For the lowest No-Term alarm monitoring rates contact GEOARM Security.
Contact: http://www.geoarm.com/contact.html
Product: http://www.geoarm.com/vista-21ip-honeywell-dual-path-security-system.html
Alarm Monitoring for new or existing systems : http://www.geoarm.com/alarm-monitoring-services.html

 

Facebooktwittergoogle_plusredditpinterestlinkedinmail

 Honeywell 3GL Cellular Communicator: How to Locate MAC And CRC Serial Number’s

DIY How to Locate MAC And CRC Serial Number’s on the Honeywell 3GL Cellular Communicator. This is the number that will be needed upon trying to activate your professional central station monitoring with GEOARM! This communicator is also one of the main reasons why the lynx touch series wireless alarm systems are able to use total connect 2.0 interactive alarm monitoring.

For the lowest No-Term alarm monitoring rates contact GEOARM Security.
Contact: http://www.geoarm.com/contact.html
Product: http://www.geoarm.com/3gl-honeywell-lynx-touch-3g-cellular-alarm-communicator.html
Alarm Monitoring for new or existing systems : http://www.geoarm.com/alarm-monitoring-services.html

Facebooktwittergoogle_plusredditpinterestlinkedinmail

 Honeywell LYNX Touch L7000: DIY How to Install the 3GL Cellular Communicator

Today I am going to show you how to install the 3GL cellular communicator into the LYNX Touch L7000 wireless security system. Note: Before working with your Honeywell LYNX touch L7000 unplug the backup battery and make sure the L7000 transformer is detached from any power outlet. Organize all of the contents of the wireless security system and the cellular communicator. You will be working with three screws, the 3gl module, and the cellular card. When opening all of these boxes make sure to keep packaging in re sell-able condition in case you need to return the items for any reason.
Depress the two tabs located on the top of the Honeywell L7000 wireless security system. I like to you use a small flat head screw to open the panel. Take the GSM chip that comes with the 3gl cellular communicator. Locate the side on the chip that says GSM. That part will slide into the female slot on the 3gl cellular communicator. Once that has been completed locate the 3 screw terminals in the bottom left of the system and as shown on our video. Align the screws and communicator in their designated slots. Once all three screws have been inserted your communicator is now in place. Locate the Mac and Mac Crc numbers off of the communicator and make note of that as you will need this to activate cellular monitoring with GEOARM. Plug in your backup battery make sure your transformer is wired correctly, seal the panel up and plug in your transformer and Call us so we can schedule your tech appointment to go online with our remote tech support!

DIY How to install the 3GL Cellular Communicator into the LYNX touch L7000 wireless security system.

For the lowest No-Term alarm monitoring rates contact GEOARM Security.
Contact: http://www.geoarm.com/contact.html
Product: http://www.geoarm.com/3gl-honeywell-lynx-touch-3g-cellular-alarm-communicator.html
Alarm Monitoring for new or existing systems : http://www.geoarm.com/alarm-monitoring-services.html

Facebooktwittergoogle_plusredditpinterestlinkedinmail

 Honeywell LYNX Touch L5200: DIY How to Install the 3GL Cellular Communicator?

 

Today i am going to show you how to install the 3GL cellular communicator into the LYNX Touch L5200 wireless security system. Note: Before working with your Honeywell LYNX touch l5200 unplug the backup battery and make sure the l7000 transformer is detached from any power outlet. Organize all of the contents of the wireless security system and the cellular communicator. You will be working with three screws, the 3gl module, and the cellular card. When opening all of these boxes make sure to keep packaging in re sell-able condition in case you need to return the items for any reason.

Depress the two tabs located on the top of the Honeywell L5200 wireless security system. I like to you use a small flat head screw to open the panel. Take the GSM chip that comes with the 3gl cellular communicator. Locate the side on the chip that says gsm. That part will slide into the female slot on the 3gl cellular communicator. Once that has been completed locate the 3 screw terminals in the bottom left of the system and as shown on our video. Align the screws and communicator in their designated slots. Once all three screws have been inserted your communicator is now in place. Locate the Mac and Mac Crc numbers off of the communicator and make note of that as you will need this to activate cellular monitoring with GEOARM. Plug in your backup battery make sure your transformer is wired correctly, seal the panel up and plug in your transformer and Call us so we can schedule your tech appointment to go online with our remote tech support!

Facebooktwittergoogle_plusredditpinterestlinkedinmail